Streambox Admin

Enter your Locusonus Soundmap stream/account.

login:
password:

If you have multiple sound cards connected, select the card interface number to use for streaming.

sound card:

Or create (and use) a virtual two-channel device with the two first audio input.
This virtual stereo device is in fact two interleaved mono streams, the real devices will drift out of sync over time.

create a virtual stereo device

Audio output configuration.
Audio quality 0 is roughly equivalent to 64kbps average, 0.5 is roughly 160kbps, and 1 gives about 400kbps. Most people seeking very-near-CD-quality audio encode at a quality of 0.5 or, for lossless stereo coupling, 0.6. The default setting is quality 0.3.

audio samplerate: 8000 Hz 11025 Hz 16000 Hz 22050 Hz 32000 Hz 44100 Hz 48000 Hz
audio channel: mono stereo
audio quality: 0.3

To test your wireless connection with parameters below: turn it on/off, search for networks (etc.), see the network section below.
Ethernet and USB tethering are always enabled (using the DHCP protocol by default)

turn on Wireless connection on boot
WIFI SSID *: is a hidden network
WIFI key: is a hexadecimal key
WIFI security: None WEP WPA/WPA2

To test your USB modem connection, see the network section below.
Ethernet and USB tethering are always enabled (using the DHCP protocol by default)

turn on USB modem connection on boot
APN:
modem PIN:
phone number:
user name:
password:

This generates AT commands specific to certain Huawei modems.
All other devices should use "none"

modem mode: None 3G first 3G only GPRS first GPRS only

To use your phone Wi-Fi access point (hotspot), configure the wireless settings above.

To tether your IPhone device over USB:
- enable Personal Hotspot on your iPhone and plug it into your streambox using an USB cable.
Settings -> Personal Hotspot

To tether your Androïd smartphone over USB:
- connect the phone to your streambox using an USB cable.
- Enable the tethering option from your phone. This is usually done from Settings -> Wireless & Networks -> Internet tethering (or Tethering & portable hotspot for more recent versions).

automatic (DHCP address)

Specify the hostname for this stream box.
This is optional but could be usefull if you have multiple RPI device connected to the same network.

  - to check your stream status or configure this file via HTTP, use this address:
    http://[HOSTNAME].local/
  - for maintenance and for experimented user, you can access to this stream box using this command:
    ssh locusonus@[HOSTNAME].local (password: locusonus)
  - to access or transfert to/from this stream box via SFTP, use this parameters:
    server: [HOSTNAME].local
    username: root (password:locusonus)

The HOSTNAME should be an internet-style hostname, only the ASCII letters 'a' through 'z' (in a case-insensitive manner, lower case is safer), the digits '0' through '9', and the hyphen ('-'). No other symbols, punctuation characters, or white space are permitted.
The original specification (RFC 952) mandated that hostnames could not start with a digit or with a hyphen, and must not end with a hyphen.
Limit the hostname to 63 characters, which is the length of a DNS label.
For examples, read the end of this documentation

hostname:

Enable this service to configure and access your stream box remotely.
To map a particular port on your router, enter the appropriate HTTP and/or SSH port in fields below, or leave blank to use a random port number.

From outside, go to your Locusonus Soundmap stream/account to retrieve your stream box remote address.
note: UPnP must be activated on your router to open automatically NAT/PAT rules.

turn on remote access service on boot
HTTP port:
SSH port:

Enable or disable the LED status display (web and on Air).
For more informations, read this documentation

turn on/off your LED status display